การติดตั้ง Digital Cluster ของ VW Touareg 7L 2003–2010: ขั้นตอนภาพถ่ายจริง 37

Start with the car exactly as it arrived. The first photo is the reference for the original cluster position, the surrounding trim and the overall dashboard fit. Take your own photo at this point as well; it gives you something concrete to compare against when the new cluster and trim are back in place.

Remove the screw shown around the steering-wheel area. This is the first fastening point in the photographed sequence and opens the way to the trim that comes off next.

After the screw is out, gently release the trim piece shown around the steering-wheel area. Work from the visible seam and free the piece progressively rather than trying to pull the whole section off in one movement.

Move to the side of the instrument area and release the side trim shown in the photo. This begins separating the trim pieces that lock the cluster surround into the dashboard.

Continue across both sides of the cluster surround. Once the side pieces are loose, the upper trim can be removed without fighting against panels that are still clipped together.

Release the upper decorative piece above the cluster. Removing this panel exposes the next fastening points in the installation sequence.

With the upper trim out of the way, remove the screws that are now visible. These fasteners hold the surrounding structure that must come off before the cluster mounting brackets can be reached.

The next photo returns to the side trim. Release the remaining pieces on both sides and keep the trim supported as it comes away from the dashboard.

Now remove the remaining upper trim section shown in the photo. At this point the cluster mounting structure begins to become fully visible.

Remove the screws holding the instrument mounting bracket. This is the point where the job changes from decorative-trim removal to removing the structure that physically locates the cluster.

With its screws removed, take out the first bracket shown in the sequence. Keep it together with its fasteners because it is part of the original mounting reference.

Remove the second bracket in the same area. Once both bracket pieces are out, the dashboard opening is clear enough to compare with the new cluster route.

Pause here and compare your dashboard opening with the photo. This is the most useful point to catch a fitment mismatch before any new hardware is connected or pushed into place.

Connect the main power cable to the new LCD cluster as shown. The connector should match the supplied socket and seat in the intended orientation.

Insert the thin-wire plug shown in the photo into the matching socket on the LCD cluster. Make sure it is fully seated before the cluster is moved toward the dashboard opening.

Before the display goes into the dash, look at the completed connections shown in the photo. This is the last easy opportunity to correct a half-seated plug before the back of the cluster becomes difficult to see.

Line up the two lower mounting feet of the new LCD cluster with the original screw posts shown in the photo. Both sides should meet the factory mounting points before any screw is tightened.

Hold the cluster in its aligned position and check the gap around the housing. The unit should sit naturally in the opening rather than being pulled into shape by the screws.

Move the cluster into its final dashboard position. Keep the wiring behind the unit free as the housing moves inward so the front fit is not achieved at the expense of a trapped cable behind it.

The source sequence now introduces the extension cable that runs from the cluster area toward the passenger-side glovebox. Route it along the documented path and leave enough length for the retained original mainboard that is connected later.

Once the cluster is aligned and the extension cable has a clear route, install the mounting screws. Tighten the unit in the position it already sits correctly rather than using the screws to pull the housing into alignment.

Clip the new cluster trim into place around the display. Work around the edge and confirm that the trim sits evenly with the dashboard opening.

Return the original trim pieces to both sides of the cluster. This is the first visual check that the new assembly is sitting where the original dashboard expects it to sit.

The job now moves to the original instrument cluster itself. Remove the screw shown in the photo so the original housing can be opened. From this point onward, the original cluster is being disassembled because part of its electronics will remain in the vehicle.

Carefully separate the original instrument housing. The goal is not simply to dismantle the old cluster; it is to reach the electronics that the photographed retrofit route keeps and relocates.

Lift off the pointers shown in the source photo so the cluster can be opened further. Keep the removed original parts together while the board-transfer stage is completed.

Open the lower housing shown in the photo. This exposes the internal connection and the original instrument mainboard used in the next steps.

Unplug the internal cable shown inside the original cluster. Once this connection is released, the mainboard can be separated from the original housing.

This is the defining technical step in this installation route: the original Touareg instrument mainboard is kept. The source sequence does not discard it; the board continues into the final installation.

Position the original mainboard on the supplied metal support exactly as shown in the photo. The support gives the board a stable mounting method after it leaves the original instrument housing.

Check the finished board mounting before moving it to the passenger side. The board should remain fixed to the support with its connection point available for the wiring shown later.

Move to the passenger side and release the side panel beside the glovebox. This begins the access path for the extension cable and the retained original mainboard.

Remove the additional trim piece shown around the glovebox area. Only the panels needed to reach the storage compartment and board location are being opened.

Remove the screws holding the glovebox/storage compartment. This creates the working space needed to connect and position the retained original instrument mainboard.

Connect the wiring to the retained original mainboard as shown. This connection completes the route that began when the extension cable was pulled across from the new cluster in Step 20.

Position the retained original mainboard in the passenger-side glovebox area following the photographed arrangement. Before the glovebox is closed, confirm that the board remains fixed to its support and the wiring has enough room to stay connected without being pinched.

The original source describes the final step as the finished installation result, but the extracted step set does not contain a separate Step 37 image. Before normal use, power the vehicle on and verify the functions that apply to the confirmed cluster version.